S918 describes Delivery Confirmation, the classes of mail that may include this service, and the retail and electronic delivery options.
Delivery Confirmation service provides the mailer with information about the date and time an article was delivered and, if delivery was attempted but not successful, the date and time of the delivery attempt. Delivery Confirmation service is available only at the time of mailing. No record is kept at the office of mailing. Delivery Confirmation service does not include insurance, but insurance may be purchased as an additional service (see 1.6). Some statutes and regulations governing the mailing of documents with legal significance may require the use of Certified Mail or Registered Mail rather than Delivery Confirmation.
Delivery Confirmation is available for First-Class Mail parcels defined in C050 as machinable (with no minimum weight), irregular, or outside parcels; for all Priority Mail pieces; for Standard Mail pieces subject to the residual shape surcharge (electronic option only); and for Package Services parcels defined in C050 as machinable, irregular, or outside parcels. For the purposes of using Delivery Confirmation with a First-Class Mail parcel or a Package Services parcel, the parcel must meet these additional requirements:
a. The surface area of the address side of the parcel must be large enough to contain completely and legibly the delivery address, return address, postage, and any applicable markings, endorsements, and special service labels.
b. Except as provided in 1.2c for machinable parcels, the parcel must be greater than 3/4 inch thick at its thickest point.
c. If the mailpiece is a machinable parcel under C050 and no greater than 3/4 inch thick, the contents must be prepared in a strong and rigid fiberboard or similar container or in a container that becomes rigid after the contents are enclosed and the container is secured. The parcel must be able to maintain its shape, integrity, and rigidity throughout processing and handling without collapsing into a letter-size or flat-size piece.
Delivery Confirmation is not available for the following:
a. Express Mail and Periodicals pieces.
b. First-Class Mail letter-size and flat-size pieces.
c. Standard Mail pieces not subject to the residual shape surcharge and all Enhanced Carrier Route Standard Mail pieces.
d. Package Services flat-size pieces.
e. Mail paid with precanceled stamps.
f. Mail addressed to APO/FPO destinations.
g. Mail addressed to any U.S. territory, possession, or Freely Associated State listed in G011, with the exception of Puerto Rico and the U.S. Virgin Islands.
The two Delivery Confirmation service options are:
a. Retail option: Available at post offices at the time of mailing. A mailing receipt is provided. Mailers can access delivery information over the Internet at www.usps.com or by calling 1-800-222-1811 toll-free and providing the article number.
b. Electronic option: Available to mailers who establish an electronic link with the USPS to exchange acceptance and delivery data. No mailing receipt is provided.
The applicable Delivery Confirmation fee in R900 must be paid in addition to the correct postage. The fee and postage may be paid with postage stamps, meter stamps, or permit imprint. Precanceled stamps are not permitted as postage payment.
Delivery Confirmation may be combined with:
a. Collect on delivery (COD).
b. Insured mail.
c. Registered mail.
d. Restricted delivery, if purchased with insurance for more than $50, COD, or registry service.
e. Return receipt, if purchased with insurance for more than $50, COD, or registry service.
f. Return receipt for merchandise.
g. Special handling.
A mailer may mail articles with retail option Delivery Confirmation at a post office, branch, or station, or give articles to a rural carrier.
If three or more articles are presented for mailing at one time, the mailer may use Form 3877 provided by the USPS at no charge, or privately printed firm sheets. Privately printed or computer-generated firm sheets that contain the same information as Form 3877 may be used if approved by the local postmaster. The mailer may omit columns from Form 3877 that are not applicable to Delivery Confirmation mail. Required elements are the package identification code (PIC), 5-digit destination ZIP Code, and applicable fees. If the mailer wants the firm sheets receipted by the USPS, the mailer must present the books with the articles to be mailed at a post office. The sheets of the books are the mailers receipts. All entries made in firm sheets must be made by typewriter or ink. Alterations must be initialed by the mailer and accepting postal employee. All unused portions of the addressee column must be obliterated with a diagonal line. A receipt is required for refund requests.
Mailers must use one of the label options shown below (for additional information see Publication 91, Confirmation Services Technical Guide):
a. Form 152, obtained from the post office at no charge. This form may be used only with the retail option (see Exhibit 2.1a).
b. Label 314, available at no charge to electronic option mailers (see Exhibit 2.1b).
c. Privately printed barcoded labels that meet the requirements in 2.0 and 3.0 (see Exhibit 2.1c). On the Priority Mail label, mailers must use the registered trademark symbol following the Priority Mail text or add the following statement at the bottom of the label in at least 6-point Helvetica type: Priority Mail is a registered trademark of the U.S. Postal Service.
Exhibit 2.1aForm 152
Exhibit 2.1bLabel 314
Exhibit 2.1cPrivately Printed Label
The barcoded label section of Label 314 or Form 152 must be placed either above the delivery address and to the right of the return address or to the left of the delivery address. A privately printed Delivery Confirmation label that is separate from the address label must be placed in close proximity to the address label. In all cases, the entire Delivery Confirmation label must be placed on the address side and not overlap any adjacent item.
[4-1-04] Labels printed by mailers must meet the following barcode symbology requirements:
a. Mailers printing their own barcodes and using the retail service option (1.4a) must use the Automatic Identification Manufacturers' (AIM) Uniform Specifications for USS Code Interleaved 2 of 5 barcode symbology. Each barcode must contain a unique Package Identification Code (PIC) as specified in 3.2. Barcodes also must meet the specifications in Publication 91.
b. Effective January 31, 2005, mailers printing their own barcodes and using the electronic service option (1.4b) must use the UCC/EAN Code 128 barcode symbology. All new mailers must use this symbology. Through January 30, 2005, mailers printing their own barcodes and using the electronic service option may use one of the following barcode symbologies: UCC/EAN Code 128, USS Code Interleaved 2 of 5, USS Code 39, or USS Code 128. Each barcode must contain a unique PIC as specified in 3.2. Barcodes also must meet the specifications in Publication 91. Refer to DMM S923 for Delivery Confirmation with Merchandise Return Service.
Each barcode symbology must contain a unique PIC:
a. For UCC/EAN 128, each barcode must contain a unique PIC and be made up of five fields totaling 22 characters. Additional information and specifications can be found in Publication 91. The five required data fields are:
(1) Application Identifier (AI): two characters; identifies the article as a Delivery Confirmation piece.
(2) Service Type Code (STC): two characters; identifies the type of product or service used for each item.
(3) Customer ID: nine characters; DUNS® number that uniquely identifies the customer.
(4) Package Sequence Number (PSN): eight characters; fixed sequential number.
(5) Modulus 10 Check digit: one character.
b. For USS Code Interleaved 2 of 5, USS Code 39, and USS Code 128, each barcode must contain a unique PIC and be made up of four fields totaling 20 characters. The four required data fields are fields 2 through 5 above. Additional information and specifications can be found in Publication 91. These symbologies do not use an Application Identifier (AI).
Labels printed by mailers must meet the following specifications:
a. Each barcoded label must bear a unique Delivery Confirmation PIC barcode as specified in 3.2. The text USPS DELIVERY CONFIRMATION (if using retail service option, as specified in 1.4) or e/USPS DELIVERY CONFIRMATION (if using electronic service option, as specified in 1.4, and the postage is evident on the mailpiece) must be printed between 1/8 inch and 1/2 inch above the barcode in minimum 12-point bold sans serif type. Additionally, mailers approved for the electronic service option, at their discretion, may print the text ELECTRONIC RATE APPROVED #[DUNS® NUMBER] in minimum 8-point bold sans serif type directly below the bottom horizontal identification bar (see Exhibit 3.3). Human-readable characters that represent the barcode ID must be printed between 1/8 inch and 1/2 inch under the barcode in minimum 10-point bold sans serif type. These characters must be parsed in accordance with Publication 91. A minimum 1/8-inch clearance must be between the barcode and any printing. The preferred range of widths of narrow bars and spaces is 0.015 inch to 0.017 inch. The width of the narrow bars or spaces must be at least 0.013 inch but no more than 0.021 inch. All bars must be at least 3/4 inch high. Minimum 1/16-inch bold bars must appear between 1/8 inch and 1/2 inch above and below the human-readable endorsements to segregate the Delivery Confirmation barcode from other areas of the shipping label. The line length should extend across the width of the label but must extend the length of the barcode at a minimum (see Exhibit 2.1c). Only information relating to Delivery Confirmation and other special services must be placed between these lines.
b. Each barcode must meet the requirements in 3.1 for the type of service requested.
c. Mailers must obtain USPS certification for each printer used to print barcoded Delivery Confirmation labels. For certification, a mailer must forward for evaluation and approval 20 barcoded labels/forms generated by each printer to the National Customer Service Center (NCSC), Attention Barcode Certification (see G043 for address). The USPS will issue the mailer a Form 3152 for each printer certified. All barcodes must be in accordance with 2.0 and 3.0. Further certification instructions are included in Publication 91.
d. Barcodes that do not meet specifications will not be accepted by the USPS. The USPS will contact the mailer if problems with the barcodes are found and will try to resolve the problem. The USPS may suspend a mailers certification if electronic file quality does not meet specifications.
Exhibit 3.3Electronic Service Option Identification
An integrated barcode may be used by mailers printing their own barcodes and using the electronic service option. Mailers may combine Delivery Confirmation and insurance services into a single barcode on the shipping label and eliminate multiple labels and barcodes on packages. Mailers must still meet existing specifications in 3.1 and 3.2. Minor modifications allow users to request multiple special services on Priority Mail and Package Services. Two required changes are:
a. Change the text above the barcode to identify the service requested. Exhibits are included in Publication 91.
b. Change the service type code in the barcode to identify the class of mail and/or type of special services combined with Delivery Confirmation. Additional information on the Service Type Code Matrix can be found in Publication 91.
Mailers must meet the following standards for electronic file transmission:
a. Publication 91 contains specifications for electronic file transmission. A test file transmission must be uploaded and approved before mailings begin. Upon certification, the USPS will issue the mailer Form 3152.
b. Mailers using the electronic option must transmit a file with a unique record for each article mailed. The USPS will contact the mailer if problems with the file are found and will try to resolve those problems. The USPS may suspend a mailers certification if the electronic file quality does not meet specifications. In addition, USPS acceptance units will be notified to charge the customer the retail Delivery Confirmation fee.
c. Mailers using the electronic option must include additional fields in the electronic file when planning to use the integrated barcode. For more information consult Publication 91.
Customers must meet the following requirements when presenting electronic option Delivery Confirmation mail for acceptance:
a. Presorted or permit imprint mailings containing pieces for which fees are paid for Delivery Confirmation service must be presented to a post office business mail entry unit (BMEU), detached mail unit (DMU) at the mailers plant, bulk mail center or auxiliary service facility business mail entry unit, or other postal facility capable of properly verifying the mailing and at which the mailer has obtained the necessary permits or license and paid any applicable mailing fee.
b. Mailers who use the electronic option or print their own labels must submit a copy of the original Form 3152 with their first mailing using Confirmation Services (see exception in 5.0c). The business mail or detached mail entry unit office will retain a copy of the form. However, mailers who wish to obtain an electronic entry scan must submit Form 3152 with each mailing to include the electronic file number associated with that mailing. The electronic file number on the form must be in either a barcode format (preferred) or written on the form. All barcode formats must comply with the standards in Publication 91. Mailers should keep the certification form on file while using Confirmation Services. If requested by the Postal Service, the form must be presented within 24 hours.
c. Mailers of single-piece rate mail with postage affixed using the electronic option rate are not required to submit Form 3152 with their initial mailing. This includes mailings generated from the Postal Service online shipping label application at www.usps.com or labels generated from a third-party vendor or system that supports the electronic option rates. All labels must meet USPS format and design requirements, including the e (electronic rate) endorsement in the barcode text line.
DMM Issue 58 Updated 12-9-04