USPS Homepage Skip NavigationUSPS Home | Postal Explorer Home | Privacy Policy
  DMM TOC > 200 Commercial Mail > 220 Priority Mail

225 Mail Preparation

1.0 General Information for Mail Preparation

1.1 Priority Mail Packaging Provided by the USPS

Priority Mail packaging provided by the USPS must be used only for Priority Mail. Regardless of how the packaging is reconfigured or how markings may be obliterated, any matter mailed in USPS-provided Priority Mail packaging is charged the appropriate Priority Mail price. Any matter mailed in USPS-produced Critical Mail packaging will be charged Critical Mail prices only if all applicable standards in 223 are met; otherwise such matter will be charged the Priority Mail Commercial Plus Flat Rate Envelope price.

1.2 Sealing Flat Rate and Regional Rate Packaging

[6-2-14] When sealing a Flat Rate Envelope, Flat Rate Box, or Regional Rate Box, the container flaps must be able to close within the normal folds. Tape may be applied to the flaps and seams to reinforce the container; provided the design of the container is not enlarged by opening the sides and the container is not reconstructed in any way.

1.3 Required Use of Return Address

The sender's domestic return address must appear legibly on Priority Mail pieces.

Back to Top

2.0 Markings

[6-2-14] The marking “Priority Mail” must be placed prominently on the address side of each piece of Priority Mail. See 202.3.3 for price and other markings.

Back to Top

3.0 Preparation of Permit Imprint Mailings

3.1 Identical Weight Pieces

To use a permit imprint, the pieces must be of identical weight and, unless all the pieces are in a weight category for which the price does not vary by zone, the pieces must be separated by zone when presented to the Post Office, except under 3.2.

3.2 Nonidentical Weight Pieces

A permit imprint may be used for mailings of nonidentical-weight pieces only if authorized by Business Mailer Support at USPS Headquarters.

Back to Top

4.0 Additional Standards for Preparing Critical Mail

4.1 Preparing Critical Mail Letters in Trays

[6-2-14] When mailing 200 or more Critical Mail letters in one mailing, prepare the letters in USPS-provided letter trays with the letters “faced” (oriented with all addresses in the same direction with the postage area in the upper right). Secure and strap letter trays using USPS-provided sleeves. Label trays under the applicable letter tray label standards in 203.4.0 and as follows:

a. Line 1: Use L201; for mail originating in ZIP Code areas in Column A, use “MXD” followed by city, state, and 3-digit ZIP Code prefix in Column C (use “MXD” instead of “OMX” in the destination line and ignore Column B).

b. Line 2: “CRITICAL MAIL LTRS WKG.”

c. Line 3: Office of mailing or mailer information.

4.2 Preparing Critical Mail Flats in Trays

[6-2-14] When mailing 200 or more Critical Mail flats in one mailing, prepare Critical Mail flats in USPS-provided flats trays with green lids, place the mail with addresses facing upward in the same direction. Place pieces in trays to maintain their orientation. The weight of a tray and its contents must not exceed 70 pounds. Cover each tray with the green side of the lid facing up and secure the lid with two straps placed tightly around the width of the tray. Label trays under the applicable flat tray label standards in 203.4.0 and as follows:

a. Line 1: Use L201; for mail originating in ZIP Code areas in Column A, use “MXD” followed by city, state, and 3-digit ZIP Code prefix in Column C (use “MXD” instead of “OMX” in the destination line and ignore Column B).

b. Line 2: “CRITICAL MAIL FLTS WKG.”

c. Line 3: Office of mailing or mailer information.

4.3 Postage for Critical Mail and Priority Mail

When a manifest mailing system is used, Critical Mail and Priority Mail may be entered on the same postage statement, but mailpieces must be presented separately and may not be combined or commingled in the same container.

Back to Top

5.0 Preparing a Commercial Plus Cubic Mailing

[6-2-14] Commercial Plus cubic mailpieces for multiple price tiers may be combined in the same container.