ARCHIVED QSG - NOV 07, 2011
USPS Homepage Skip navigation     USPS Home | Postal Explorer Home
Section divider line
 

Quick Service Guide 301

Commercial Flats

Physical Standards for Commercial Flats

November 7, 2011
Printer-Friendly PDF

Overview

Section divider line

Flat Dimensions

 

 

 

The graphic describes the minimum and maximum sizes for flats. Flat mail is: a. more than 11-1/2 inches long, or more than 6-1/8 inches high, or more than 1/4 inch thick; b. Not more than 15 inches long, or more than 12 inches high, or greater than 3/4 inch thick.

 

Minimum*

Maximum

Length

11-1/2 inches

15 inches

Height

6-1/8 inches

12 inches

Thickness

1/4 inch

3/4 inch

* Flats exceed at least one of these dimensions

For physical standards of automation flats, see Quick Service Guide 301a.

In addition to shape, the Postal Service classifies mailpieces by the way they are prepared. These classifications are based on how efficiently your mailpieces can be processed on Postal Service equipment. The Postal Service classifies commercial flats as either nonautomation or automation flats or machinable and nonmachinable for Periodicals.

A flat meets automation standards and qualifies for automation prices if it meets the specific addressing, barcoding, and design standards. Automation flats must have a POSTNET or Intelligent Mail barcode with a delivery point routing code.

Dimensions, Shape, Flexibility, and Uniform Thickness (301.1.0)

Section divider line

Dimensions:

The length of a flat-size mailpiece is the longest dimension. The height is the dimension perpendicular to the length.

Shape: rectangular, with four square corners, or with finished corners that do not excced a radius of 0.125 inch (1/8 inch).

Flexibility and deflection: flat-size pieces must meet flexibility criteria in 301.1.3 and the deflection criteria in 301.1.6. Flats mailed at saturation or high density prices or flats mailed at basic carrier route prices and dropshipped to DDUs do not have to meet deflection standards. All other flats not meeting deflection standards are subject to prices as stated in DMM 301.1.7.

Uniform thickness: the contents must be uniformly thick so that any bumps, protrusions, or irregularities do not cause more than 1/4 inch variance in thickness (301.1.4). When determining variance in thickness, exclude the outer edges of a mailpiece (1 inch from each edge) when the contents do not extend to the edges.

Mailpieces that do not meet the standards for flexibility in 301.1.3, for uniform thickness in 301.1.4, or for polywrap in 301.1.5, must pay applicable prices as follows:

Presorted Nonautomation Flats (301.2.0)

Section divider line

Maximum weight:

Automation Flats (301.3.0)

Section divider line

Flats may qualify for the automation discount based on the physical standards in 301.3.0.

See Quick Service Guide 301a, Designing Flats for Automated Processing, for an overview.

Standard Mail Not Flat-Machinable Pieces (401.2.4)

Section divider line

For Standard Mail Not Flat-Machinable pieces, see Quick Service Guide 401.

Quick Service Guides

Section divider line

First-Class Mail

See Quick Service Guides:

330a Nonautomation Flats

330b Automation Flats

Standard Mail

See Quick Service Guides:

340a Nonautomation Flats

340b Automation Flats

340c Carrier Route Flats

Bound Printed Matter

See Quick Service Guide:

360 Flats

Media Mail and Library Mail

See Quick Service Guide:

370 Presorted Flats

Periodicals

See Quick Service Guides:

707e Nonmachinable Flats

707g Barcoded (Automation) Flats

 

Back to Top


ARCHIVED QSG - NOV 07, 2011
ARCHIVED QSG - NOV 07, 2011