DMM TOC > 200 Discount Letters and Cards|
The delivery address specifies the location to which the USPS is to deliver a mailpiece. Except for mail prepared with detached address labels under 602.4.0, the piece must have the address of the intended recipient, visible and legible, only on the side of the piece bearing postage. (See 2.0 for address placement; see 602 for additional information regarding addressing.)
The location of the delivery address on a letter-size mailpiece determines which dimensions are the length and height of the piece. The length is the dimension parallel to the address as read; the height is the dimension perpendicular to the length. Consequently, the placement of the address may render a piece nonmailable or nonmachinable. On a letter-size piece, the recommended address placement is within the optical character reader (OCR) read area, which is a space on the address side of the mailpiece defined by these boundaries (see Exhibit 2.1, OCR Read Area):
Enclosures, attachments, and mixed rate mailpieces must be marked under the applicable standards in 703.9.0, Mixed Classes.
a. Basic Marking. The basic required marking that indicates the class or subclass—"First-Class," "Presorted Standard" or "PRSRT STD," or "Nonprofit Organization" (or "Nonprofit Org." or "Nonprofit")—must be printed or produced as part of, or directly below or to the left of, the permit imprint indicia, meter stamp or impression, or adhesive or precanceled stamp.
b. Other Markings. The rate-specific markings "AUTO," "Presorted" (or "PRSRT"); "Single-Piece" (or "SNGLP") (First-Class Mail only); and "ECRLOT," "ECRWSH," "ECRWSS," and "Customized MarketMail" (or "CUST MKTMAIL" or "CMM") (Standard Mail only) may be placed as follows:
1. In the location specified in 3.3a..
2. In the address area on the line directly above or two lines above the address if the marking appears alone or if no other information appears on the line with the marking except optional endorsement line information under 708.7.0 or carrier route bundle information under 708.6.0.
3. If preceded by two asterisks (**), the "AUTO," "PRESORTED" (or "PRSRT"), "CUSTOMIZED MARKETMAIL" (or "CUST MKTMAIL" or "CMM"), or "Single-Piece" (or "SNGLP") marking also may be placed on the line directly above or two lines above the address in a mailer keyline or a manifest keyline, or it may be placed above the address and below the postage in an MLOCR ink-jet printed date correction/meter drop shipment line. Alternatively, the "AUTO," "PRSRT," or "SNGLP" marking may be placed to the left of the barcode clear zone (subject to the standards in 5.0, Barcode Placement) on letter-size pieces.
c. Additional Requirements for Carrier Route. "ECRLOT," "ECRWSH," and "ECRWSS" (Standard Mail only) must appear in their entirety wherever placed, except "ECR" may be placed in the postage area if "LOT," "WSH," or "WSS," as applicable, is placed in the line above or two lines above the address, as specified in 3.3b.. Pieces not mailed at ECR rates must not bear these markings.
a. Automation Letters. First-Class Mail and Standard Mail letters do not require an "AUTO" marking if they bear a DPBC or an Intelligent Mail barcode with a delivery point routing code in the address block or on an insert visible through a window. First-Class Mail letters not marked "AUTO" must bear both the "Presorted" or "PRSRT" and "First-Class" markings. Standard Mail letters not marked "AUTO" must bear the appropriate basic marking in 3.3a.
b. Manifest Mailings. The basic marking must appear in the postage area on each piece as required in 3.3a. The two-letter rate category code required in the keyline on manifest mailing pieces prepared under 705.2.0, Manifest Mailing System, meets the requirement for other rate markings.
c. MLOCR Prepared Automation Mailings. The basic marking must appear in the postage area on each piece as required in 3.3a.. The other "AUTO" marking described in 3.3b. must be replaced by the appropriate identifier/rate code marking described in 705.5.0, First-Class Mail or Standard Mail Mailings With Different Payment Methods, on those pieces that have the marking applied by an MLOCR. This seven-character marking provides a description of the Product Month Designator, MASS/FASTforward System Identifier, postage payment method, and the rate of postage affixed for metered and precanceled stamp mail or other postage information for permit imprint mail.
All mailable hazardous materials must be labeled and/or marked as required in 601.10.0.
The mailer must place the correct endorsement on each mailpiece to provide delivery instructions (retention period under 507.3.4.4 or carrier release under 508.1.2) or to request an ancillary service (forwarding, return, or address correction under 507.1.0, Treatment of Mail), subject to the corresponding standards for use and availability.
When an ancillary service endorsement is used, a domestic return address must be placed in the upper left corner of the address side of the mailpiece or the upper left corner of the addressing area. If the return address is a multiple delivery address, it must show a unit designator (e.g., an apartment number).
a. The carrier release endorsement must be placed directly below the return address. If any other endorsement is used, the carrier release endorsement must be separated by the equivalent of one blank line of the type size used.
d. A clear space of at least 1/4 inch around (above, below, and both sides) the total area containing the endorsement(s) is required. This 1/4-inch clear space is not required for an endorsement that is applied with a multiline optical character reader (MLOCR) inkjet and placed in the location directly below the postage area and any rate marking if the endorsement is clear and legible.
Each letter-size piece in an automation rate mailing or claimed at an Enhanced Carrier Route saturation or high density rate must have a barcode clear zone unless the piece bears a DPBC or an Intelligent Mail barcode with a delivery point routing code (see 708.4.3) in the address block. The barcode clear zone and all printing and material in the clear zone must meet the reflectance standards in 708.4.4. The barcode clear zone is a rectangular area in the lower right corner of the address side of cards and letter-size pieces defined by these boundaries:
Automation rate letters and letters claimed at an Enhanced Carrier Route saturation or high density rate may bear a DPBC or an Intelligent Mail barcode with a delivery point routing code (see 708.4.0). Mailers must print the barcode either in the address block or in the barcode clear zone, except that pieces in a OneCode ACS mailing and pieces that weigh more than 3 ounces must include the barcode in the address block. An Intelligent Mail barcode placed in the address block, when used with OneCode ACS (see 507.3.2), must appear above the address information according to standards in 5.6.Barcode on Mailpiece
Except as noted in 5.4, 5-Digit Barcode Placement in Clear Zone, for 5-digit barcodes, if the barcode is printed directly on the mailpiece in the lower right corner, the entire barcode must be within the barcode read area defined by these limits:
b. Vertically, the barcode must be within the area between 3/16 inch and 7/16 inch from the bottom edge of the piece; the bottom of the bars must be 1/4 inch ±1/16 inch from the bottom edge of the piece.
An automation rate letter-size piece may not bear a 5-digit or ZIP+4 barcode in the lower right corner (barcode clear zone). The piece may bear a 5-digit or ZIP+4 barcode in the address block only if a DPBC or an Intelligent Mail barcode with a delivery point routing code appears in the lower right corner. The ZIP+4 barcode may appear in the address block when printed on an insert that appears through a window or on an address label affixed directly to the piece; or it may appear in the lower right corner either printed directly on the mailpiece or on an insert that appears through a window.
Any 5-digit barcode must be located as specified in 5.3, except that, if placed in the barcode clear zone, the leftmost bar of the barcode must be between 4-1/8 and 4-1/4 inches from the right edge of the mailpiece.
In delivery point barcoded automation rate mailings only, the numbers corresponding to the POSTNET bars in a correct delivery point barcode (DPBC) may appear in the delivery address. If read from left to right, a correct DPBC numeric equivalent consists of five digits, a hyphen, and seven digits.
2. Below the city, state, and ZIP Code line, except when using an Intelligent Mail barcode to access OneCodeACS (see 507.3.2).
c. The minimum clearance between the barcode and any information line above or below it within the address block must be at least 1/25 inch, and the separation between the barcode and top line or bottom line of the address block must not exceed 5/8 inch. The clearance between the leftmost and rightmost bars and any adjacent printing must be at least 1/8 inch.
d. If a window envelope is used, the clearance between the leftmost and rightmost bars and any printing or window edge must be at least 1/8 inch, and the clearance between the barcode and the top and bottom window edges must be at least 1/25 inch. These clearances must be maintained during the insert's range of movement in the envelope. Address block windows on heavy letter mail (as defined in 5.2, General Barcode Placement for Letters) must be covered; such windows may be covered on other mail. Covers for address block windows are subject to 5.10.
e. If an address label is used, a clear space of at least 1/8 inch must be left between the barcode and the left and right edges of the address label, and the clearance between the barcode and the top and bottom edges of the address label must be at least 1/25 inch.
f. The rightmost bar must be at least 1/2 inch from the right edge of the mailpiece, and the leftmost bar must be less than 10-1/2 inches from the right edge of the mailpiece and at least 1/2 inch from the left edge of the mailpiece; the top of each bar must be less than 4 inches from the bottom edge of the mailpiece; and the bottom line of the address block, including the barcode, must be at least 5/8 inch from the bottom of the mailpiece.
c. When the insert showing through the window is moved to any of its limits inside the envelope, the entire barcode must remain within the barcode clear zone, and a clear space must be maintained that is at least 1/8 inch between the barcode and the left and right edges of the window, at least 1/25 inch between the barcode and the top edge of the window, and at least 3/16 inch between the barcode and the bottom edge of the mailpiece.
A barcode window must extend fully to the bottom edge of the envelope, must be of wraparound construction, and must be covered subject to 5.10.
The window cover must be of a nontinted clear or transparent material (e.g., cellophane or polystyrene) that permits the barcode and its background, as viewed through the window material, to meet the reflectance standards in 708.4.4. The edges of the window cover must be securely glued to the envelope.