DMM TOC > 400 Discount Parcels|
The delivery address specifies the location to which the USPS is to deliver a mailpiece. Except for mail prepared with detached address labels under 602.4.0, the piece must have the address of the intended recipient, visible and legible, only on the side of the piece bearing postage. (See 602 for additional information regarding addressing.)
a. Basic Marking. The basic required marking that indicates the class or subclass—"First-Class," "Presorted Standard" or "PRSRT STD," or "Nonprofit Organization" (or "Nonprofit Org." or "Nonprofit")—must be printed or produced as part of, or directly below or to the left of, the permit imprint indicia, meter stamp or impression, or adhesive or precanceled stamp.
1. In the location specified in 2.1.1a.
2. In the address area on the line directly above or two lines above the address if the marking appears alone or if no other information appears on the line with the marking except optional endorsement line information under 708.7.0 or carrier route bundle information under 708.6.0.
3. If preceded by two asterisks (**), the "PRESORTED" (or "PRSRT") or "CUSTOMIZED MARKETMAIL" (or "CUST MKTMAIL" or "CMM") marking also may be placed on the line directly above or two lines above the address in a mailer keyline or a manifest keyline, or it may be placed above the address and below the postage in an MLOCR ink-jet printed date correction/meter drop shipment line.
c. Additional Requirements for Carrier Route. "ECRLOT," "ECRWSH," and "ECRWSS" (Standard Mail only) must appear in their entirety wherever placed, except "ECR" may be placed in the postage area if "LOT," "WSH," or "WSS," as applicable, is placed in the line above or two lines above the address. Pieces not mailed at ECR rates must not bear these markings.
a. The basic marking must appear in the postage area on each piece. The two-letter rate category code required in the keyline on manifest mailing pieces prepared under 705.2.0 meets the requirement for other rate markings.
b. Mail manifested using the Electronic Verification System (eVS) under 705.2.9 must bear the basic marking and the additional marking "eVS" (or the alternative "e-VS" or "EVS") in two places:
1. In the required permit imprint as described in 604.5.0.
The basic required Package Services subclass marking—"Parcel Post" or "PP," "Bound Printed Matter" or "BPM," "Media Mail," or "Library Mail"—must be printed on each piece claimed at the respective rate. For Parcel Post destination entry rate mail, the marking "Parcel Select" may be used as the basic required marking instead of "Parcel Post." The basic required marking must be placed in the postage area (i.e., printed or produced as part of, or directly below or to the left of, the permit imprint indicia or meter stamp or impression). Optionally, the basic required marking may be printed on the shipping address label as service indicators composed of a service icon and service banner (see Exhibit 2.2.1):
b. The service banner must appear directly below the postage payment area and the service icon, and it must extend across the shipping label. If the service banner is used, the appropriate subclass marking (e.g., "PARCEL POST," "MEDIA MAIL") must be preceded by the text "USPS" and must be printed in minimum 20-point bold sans serif typeface, uppercase letters, centered within the banner, and bordered above and below by minimum 1-point separator lines. There must be a 1/16-inch clearance above and below the text.
a. Destination Entry Rate Mail. Each piece mailed at a DBMC, DSCF, or DDU Parcel Post rate must bear the marking "Parcel Post" (or "PP") or "Parcel Select" in the postage area as described in 2.2.1. If "Parcel Select" is shown in the postage area, then no other marking is required. If "Parcel Post" (or "PP") is shown in the postage area, then the additional marking "Drop Ship" (or "D/S") or "Parcel Select," or both, must be placed on each piece in either the postage area or the address area (as described under 2.0) to indicate that the piece was entered at a destination entry rate.
b. Other Parcel Post Mail. Pieces must bear the marking "Parcel Post" (or "PP") in the postage area as described under 2.2.1.
Each piece in a Parcel Select (destination entry Parcel Post) mailing must bear a marking to indicate it was mailed at a destination entry rate. If the "Parcel Select" marking is used as the basic marking in the postage area on such pieces under 2.2.1, no additional marking is required because the "Parcel Select" marking identifies the mail as destination entry rate mail. If the "Parcel Post" (or "PP") marking is used as the basic marking in the postage area under 2.2.1, one or both of the following markings also must appear on each piece in the mailing to identify it as destination entry rate mail: (1) "Drop Ship" (or "D/S"); (2) "Parcel Select." These additional destination entry rate markings must appear in either the postage area described in 2.2.1 or in the address area on the line directly above or two lines above the address if the marking appears alone (i.e., if no other information appears on that line). The "Parcel Select" and "Drop Ship" (or "D/S") markings must not appear on Parcel Post mail that is entered at rates other than DBMC, DSCF, or DDU destination entry rates.
In addition to the basic marking "Bound Printed Matter" or "BPM," each piece of Bound Printed Matter mailed at a presorted or carrier route rate must bear additional rate markings. The additional markings may be placed in the postage area as specified in 2.2.1. Alternatively, these markings may be placed in the address area on the line directly above or two lines above the address if the marking appears alone, or if no other information appears on the line with the marking except postal optional endorsement line information under 708.7.0 or postal carrier route bundle information under 708.6.0. The additional rate markings are:
[7-6-06] When a Bound Printed Matter machinable parcel consists of multiple pieces for a single address secured with transparent shrinkwrap, the delivery address information and barcoded pressure-sensitive Label F or firm optional endorsement line must be visible and readable by the naked eye. Mailers must label the parcel using one of the following options:
a. A firm optional endorsement line under 708.7.0, followed by the 5-digit destination ZIP Code of the parcel.
Each piece of Media Mail mailed at a presorted rate must bear the required marking "Presorted" or "PRSRT" in addition to the basic marking "Media Mail." This additional marking may be placed in the postage area as specified in 2.2.1. Alternatively, these markings may be placed in the address area on the line directly above or two lines above the address if the marking appears alone, or if no other information appears on the line with the marking except postal optional endorsement line information under 708.7.0.
[1-4-07] Mail manifested using eVS under 705.2.9 must bear the basic marking and the additional marking "eVS" (or the alternative "e-VS" or "EVS") in two places:
a. In the required permit imprint as described in 604.5.0.
Enclosures, attachments, and mixed rate mailpieces must be marked under the applicable standards in 703.9.0, Mixed Classes.
All mailable hazardous materials must be labeled and/or marked as required in 601.10.0.
The mailer must place the correct endorsement on each mailpiece to provide delivery instructions (retention period under 507.3.4.4 or carrier release under 508.1.2) or to request an ancillary service (forwarding, return, or address correction under 507.1.0, Treatment of Mail), subject to the corresponding standards for use and availability.
When an ancillary service endorsement is used, a domestic return address must be placed in the upper left corner of the address side of the mailpiece or the upper left corner of the addressing area. If the return address is a multiple delivery address, it must show a unit designator (e.g., an apartment number).
a. The carrier release endorsement must be placed directly below the return address. If any other endorsement is used, the carrier release endorsement must be separated by the equivalent of one blank line of the type size used.
The address and barcode (see 708.5.0) must be placed squarely onto the largest surface area of the parcel, except when its shape and contents requires specific orientation for stability during processing; then the address and barcode(s) must be placed on the top. The address and barcode label(s) must not overlap any side of the parcel or other label. The barcode should be placed immediately adjacent to the delivery address and at least 1 inch from the edge of the parcel. The delivery address and barcode may be printed on an attachment or enclosure in a window envelope affixed to the parcel, subject to the reflectance standards in 708.5.8. The barcode may be placed on a separate label or in an alternate location on the address label, subject to the clearance standards in 4.2. Barcodes that are not placed immediately adjacent to the delivery address must not encroach the return address, postage, applicable markings, endorsements, and extra service labels.
The barcode must be located as specified in 4.1. No printing may appear in an area 1/8 inch above and below the barcode. A minimum clear (quiet) zone equal to 10 times the average measured narrow element (bars or space) width must be maintained to the left and right of the barcode.